Manual Transmission Exam 2 Practice

These questions are part of the practice quiz. Start practicing

• What is the main function of the differential pinion gears in a transaxle?
• What is a consequence of riding the clutch?
• What is an important maintenance practice for prolonging manual transmission life?
• What occurs when a five-speed transmission is in third gear?
• What is the purpose of synchronizers in manual transmissions?
• What would be an outcome of worn countershaft bearings according to Technician B?
• In a vehicle with a transaxle, what is primarily affected by the lubrication system?
• Drive axle shafts are also called ________.
• What does the neutral position do in a manual transmission?
• What is the purpose of the spline shape in a transmission?
• Which test is best for isolating clutch system problems?
• The last step after replacing a defective CV boot is to ________.
• Why is it important to check the fluid levels in a manual transmission?
• A defective (collapsed) engine mount on a front-wheel drive vehicle can cause a vibration. True or False?
• How do modern manual transmissions differ from older designs?
• What is the primary purpose of lubricating the splines of a drive shaft yoke?
• What might Technician A incorrectly suggest regarding a worn shift fork?
• What is the correct way to engage the parking brake in a manual vehicle?
• A four-speed transmission is making a grinding noise only while shifting into second gear. What could this be caused by?
• Which technician is correct regarding solutions to reduce torque steer?
• How is "gear ratio" defined in the context of manual transmissions?
• How does proper clutch use affect manual transmission performance?
• What does a short throw shifter improve in a manual transmission?
• What can lead to a complete clutch failure?
• What is one significant advantage of overdrive for a vehicle?
• What is likely causing a noisy transmission when driving?
• Which component can limit the flexibility of the driveshaft?
• What component is used to prevent accidental engagement of reverse while making an upshift?
• When is the clutch considered fully engaged?
• What is a common symptom of a worn throw-out bearing?
• When installing a bearing over a shaft, where should force be applied?
• Why is it important to check the specified fluid type before inspecting a transmission?
• The main purpose of a reverse lockout feature is to enhance what aspect of driving?
• What is the function of the shifter in a manual transmission?
• In a transaxle, the synchronizer assemblies are mounted on which component?
• What does the term “gear ratio” refer to in manual transmissions?
• What does a “collapsed” engine mount typically cause in a vehicle?
• What is the role of a shift fork in a manual transmission?
• Which type of bearing usually requires preloading in a transaxle?
• What does "gear grinding" typically signify when shifting gears?
• What method is commonly used to adjust the bearing on many transaxle input shafts?
• What is the function of a reverse lockout mechanism in manual transmissions?
• The proper grease to use with CV joints is ________.
• What type of lubrication is commonly used in most transaxles?
• What is the function of the pilot bearing in a manual transmission?
• What can lead to smoother low-speed maneuvers in a manual vehicle?
• Which technician is correct regarding gear sizes in a transaxle?
• Torque steer in vehicles can be attributed to which of the following?
• How can engine braking be beneficial while driving?
• What is essential for proper operation of tapered roller bearings in a transaxle?
• How does the alignment of a vehicle's driveshaft impact manual transmission operation?
• In which gear would you typically find maximum engine power for acceleration?
• What was one of the earliest front wheel drive vehicles?
• What is the primary purpose of a manual transmission?
• What type of gear can be found in the gear assembly of a manual transmission?
• What are the typical gear positions found in a 5-speed manual transmission?
• Why is it not advisable to shift into reverse while moving forward in a manual vehicle?
• What can excessive slippage of the clutch result in?
• In manual transmission vehicles, which process is essential for smooth shifting?
• Which noise during operation typically suggests a problem with a throw-out bearing?
• What does it mean to "stall" a manual transmission vehicle?
• The main shaft of a transmission is also known as what?
• Why should an impact wrench be avoided for installing drive axle shaft nuts?
• When is it best to use engine braking?
• What type of joint is typically used in the rear axle of four-wheel-drive vehicles?
• Which of the following factors can cause torque steer?
• What distinguishes a synchronized transmission from an unsynchronized transmission?
• What can result from improper clutch use in a manual transmission vehicle?
• What could be a consequence of forced downshifting?
• The synchronizer sleeve's role is to do what during a shift?
• Excessive shift effort during the static shift test could be caused by which of the following?
• What tool is specifically used to check input shaft endplay?
• Which type of bearings are commonly used in manual transmissions?
• What is commonly prevented by a reverse lockout mechanism in manual vehicles?
• Excessive shift effort during testing is most likely influenced by which factor?
• Why is it crucial to follow the manufacturer's specifications for fluid and maintenance in manual transmissions?
• In a transaxle, which type of bearing is commonly used?
• What type of outer CV joints are used on front-wheel drive vehicles?
• Which of the following is a poor practice regarding manual transmission fluid?
• What is the first step in downshifting before a turn?
• How is preload in a bearing typically measured?
• Most manual transmissions use a case made from which material?
• What is the role of the clutch in a manual transmission?
• When servicing a drive axle, Technician A says that it's a good idea to tape the U-joint caps to prevent them from coming off. Technician B says that needle bearings are used with these type U-joints. Which technician is correct?
• What maintenance task should be conducted to ensure the clutch system is functioning correctly?
• When a five-speed transmission is in second gear, which statement is correct?
• Which technician is correct regarding the causes of excessive shift effort during the dynamic shift test?
• Which statement best describes the main benefit of using a manual transmission?
• In a manual transmission system, which component delivers power to the drive wheels?
• What must a driver do before downshifting in a manual transmission?
• What is the ideal RPM range for shifting up in a performance manual vehicle?
• In a manual transmission, the clutch disc must do what when engaged?
• Two technicians are discussing U-joints. Technician A says that a defective U-joint could cause a loud clunk when the transmission is shifted between Drive and Reverse. Technician B says a worn U-joint can cause a clicking sound when driving the vehicle in reverse. Which technician is correct?
• FWD driveshaft problems are usually indicated by ________.
• What does "stall speed" refer to in manual transmissions?
• Two technicians are discussing a dented driveshaft. Technician A says that it should be repaired. Technician B says it should be replaced. Which technician is correct?
• Before checking the fluid level in a manual transmission, what must a technician do?
• What is a good indicator that a manual vehicle may be experiencing transmission issues?
• Which maintenance task is essential for a manual transmission?
• Which component of a transaxle is directly connected to the clutch disc?
• What is the function of the flywheel in a manual transmission?
• The final drive ring and pinion gears in a typical transaxle utilize which type?
• Transaxle cases are typically made from which material?
• Why is it important to match engine RPM and transmission speed during shifting?
• What happens to engine performance if the manual transmission fluid levels are low?
• With the engine running and the transmission in neutral with the clutch engaged, which of the following components is NOT rotating?
• What distinguishes a transaxle from a standard transmission?
• When checking a transaxle's lubricant, where should the fluid level be?
• How are tapered roller bearings generally adjusted within a transaxle?
• What role does the transmission control module play in vehicles with automatic manual transmissions?
• What is the most likely cause of a rear-wheel drive vehicle shuddering or vibrating when starting from a stop?
• The cluster gear is supported by which of the following?
• What is the primary role of synchronizers in a manual transmission?
• What should you do to maintain safety when driving a manual vehicle in heavy traffic?
• What process might indicate a need for bearing replacement?
• Which of the following is a typical cause of manual transmission failure?
• What symptom commonly indicates problems with a driveshaft in a front-wheel drive vehicle?
• Two technicians are discussing a transaxle's differential. Which technician's statement is correct?
• How can cold temperatures affect the operation of a manual transmission?
• What is the main reason for using helical-cut gears in a transaxle?
• What does improper transmission fluid maintenance typically lead to?
• Technician A says that carbon fiber driveshafts need support bearings every 24 inches. Technician B says that carbon fiber and aluminum driveshafts reduce rotating mass and are more efficient than steel driveshafts. Which technician is correct?
• What role does transmission fluid play in a manual transmission?
• Which statement is true regarding the components in a transaxle?
• What technique can be used to smoothly start moving from a stop on an incline?
• What issue might arise from using gear oil that is too thin?
• Why is it important to maintain a safe following distance when driving a manual vehicle?
• How can blocker ring clearance be appropriately checked?
• Most transaxles primarily use which type of gears?
• How does a manual transmission generally compare to an automatic in terms of fuel efficiency?
• Which component is crucial for the prevention of gear clash during shifting?
• What is a potential risk for beginner drivers learning to use a manual transmission?
• What could occur if a driver fails to feather the clutch properly?
• Which approach is best for a technician to assess bearing wear?
• Which of the following is NOT used as CV joint boot material?
• Which type of joint is the most commonly used outer joint on FWD vehicles?
• When shifting a transaxle while the engine is running, what problem might occur?
• How can smooth driving habits affect the longevity of a manual transmission?
• During a typical upshift, the synchronizer must perform which action?
• It is recommended by many experts that an air impact wrench not be used to remove or install the drive axle shaft nut because the impacting force can damage the hub bearing. True or False?
• What is a key advantage of smooth clutch engagement when driving a manual transmission?
• Which of these could cause U-joint angles to change from their normal angles?
• What is the maximum allowable difference between front and rear working angles of a drive shaft?
• Which habit can lead to a more comfortable driving experience in a manual vehicle?
• What is the consequence of over-revving an engine in a manual transmission vehicle?
• Why is proper clutch engagement essential during takeoff?
• What component is often the cause of excessive shifting effort?
• What is a potential result of late disengagement of the clutch while shifting?
• What does the term "creep" refer to in manual transmission vehicles?
• What is the primary function of CV joints in a vehicle?
• What is an acceptable adjustment method to correct the end play in a tapered roller bearing transmission?
• Regarding synchronizer rings, which technician's statement is correct?
• A defective outer CV joint will usually make a ________.
• What is the necessary action when shifting gears to prevent grinding?
• Which condition is NOT typically associated with low transmission fluid?
• What is used in a manual transmission to achieve a clash-free shift, preventing grinding sounds?
• Are all drive shafts balanced?
• What impact does reduced weight in a manual transmission have?
• Which statement correctly describes the role of the input shaft in a manual transmission?
• What should be checked if there are issues with clutch engagement?
• What typically drives the speedometer gear?
• In what scenario would you expect to find a transmission failure?
• What needs to be removed to replace a drive axle shaft from a front wheel drive vehicle?
• What could cause noticeable vibration less at high speeds in a rear-wheel drive vehicle?
• Ensuring proper driveshaft alignment primarily benefits which aspect of the vehicle?
• The splines of the drive shaft yoke should be lubricated to prevent ________.
• What might be a consequence of not taping U-joint caps during installation?
• Why might a transmission make noise in certain gears while being quiet in others?
• Which of the following is NOT a step in checking bearings?
• What is the primary function of the main drive gear in a manual transmission?
• When replacing a CV joint boot, what must always be inspected?
• What type of oils are generally recommended for use in manual transmissions?
• Which of the following is a sign of a failing manual transmission?
• What does a transmission control module NOT do?
• What is a critical consequence of engine stalling during takeoff in manual vehicles?
• What is the primary advantage of a short throw shifter?
• What purpose does the intermediate drive shaft serve in certain front wheel drive vehicles?
• What does the term "spline" refer to in the context of transmissions?
• Which gear is most likely to use a spur gear in a manual transmission?
• When a five-speed transmission is in fourth gear, which statement is accurate?
• The detent mechanism inside a transmission is used to perform which function?
• Two technicians are discussing a transmission that is noisy in first, second, third, and reverse but quiet in fourth gear. Which technician is correct regarding the likely cause?
• What does the clutch allow the driver to do during shifting?
• What state is the engine in during a static shift test?
• In the context of torque steer on a front wheel-drive vehicle, what helps to reduce it?
• What are common symptoms of low transmission fluid in manual vehicles?
• What is the primary cause of clutch fade?
• What is the primary benefit of learning to "feather" the clutch in a manual transmission vehicle?
• What is a common indication of a worn CV joint?
• What may indicate that the transmission is slipping out of gear?
• What may occur if gears are shifted without pressing the clutch?
• Why is it important to avoid riding the clutch?
• What impact does downshifting have on vehicle performance?
• A transmission is lubricated primarily to achieve which purpose?
• A dent in an axle shaft can cause damage that may result in failure when engine torque is applied. True or False?
• The lubricant used in a manual transmission can vary. Which of the following is correct?
• If the gear shifter feels "notchy", what might be the issue?
• How is the end play in a transmission with tapered roller bearings adjusted?
• What is a sign that the clutch plate may be worn out?
• Why might a driver prefer a well-maintained manual transmission?
• What does “double clutching” involve?
• What components are typically found in a transaxle repair kit?
• If your vehicle stalls on an incline, what is the first step you should take?
• What does "rust dust" indicate in a transaxle system?
• What is the function of the clutch in a manual transmission system?
• Incorrect or unequal U-joint working angles are most likely to be caused by ________.
• Which type of gears are used for reverse in most transaxles?
• During gear changes, what can help ensure a smoother transition?